Trek II Hammond Organ Accessories

Trek II Hammond Organ Accessories

SC-60D.jpg

SC-60D-1  Frequency Conversion Units (For self starting organs) $415

SC-60D-2  Frequency Conversion Units $479

Designed specifically to supply a stable 60 HZ source for tone wheel generator organ motors.  Allows organ to play precisely in tune even in countries where the line frequency is not 60 HZ or locations where the line frequency is not stable or accurate.  Does not require additional switches or changes in the organ starting procedure. 

INPUT: 117 VOLTS 25 / 100 HZ 
OUTPUT: 110 VOLTS 60 HZ 

NOTE: Organs which have a chorus generator (BC, BCV, D, DV, G, and GV) require a special version of the SC-60D. Consult factory for details. 

NOTE: Step-down transformers as well as adaptor plugs for most countries are also available.  Contact factory for details. 


RV-1C.jpg

RV-1D  Reverberation Unit $415

For use in most standard Hammond consoles. Uses a full size three spring Accutronics delay line for a natural reverb sound. Designed specifically to interface with vacuum tube circuitry of Hammond tone wheel consoles. 

Includes reverb level control. For most installations, connection to the organ pre-amp is made with a supplied tube interface socket.

NOTE: The RV-1D is not compatible with BV, CV or DV type organs. (Specify organ models).


OBL-2 Line Output Box $97

The OBL-2 allows standard Hammond consoles to be connected via a 1/4" output jack to an external amplification system. The box is made from heavy gauge anodized aluminum and easily mounts under the generator shelf or other convenient location. The unit has both an overall output and one that is low pass filtered. The low pass output is useful when using a bass amp to reinforce the organ low end. A level control is provided to allow the output signal to be adjusted to match the amplifier input requirements. 

NOTE: Most commercial and musical instrument amplifiers are not designed for organ use and will not give the same sound quality as a Leslie or Hammond tone cabinet. However there are circumstances where connecting to an external amplifier is still desirable. These include temporary installations, rental instruments, and adding a bass amp to give the organ more low end power.

NOTE: Pre-amps in early console models (A, AB, AV, B, BA, BC, BCV, BV, C, CV, D, DV, and G) receive their DC operating voltage from the tone cabinet and will not produce an output if  the tone cabinet is disconnected.


ELB-1A.jpg

ELB-1A Effects Loop Box $138

The ELB-1A adds an INSTRUMENT LEVEL effects loop to allow the use of effects devices on either the upper or lower manual of many Hammond organ models. The ELB-1A contains an active buffer circuit which prevents the effects device from loading down the organ signal. Two ELB-1A units can be used to provide an effects loop on each manual. 

NOTES: Instrument Level effects devices include guitar pedals and other effects devices intended to be placed between an instrument and amplifier.  
Line Level effects devices are typically rack mounted and are designed to accept a higher signal level than instrument level effects devices.  
To use line level effects devices, use the SSP-3A pre-amp and the ELB-3A option.


VIB-3.jpg

VIB-3  $109

The VIB-3 makes it easy to connect your Neo Ventilator rotary cabinet simulator to any Hammond console with an existing Leslie 122. The enclosure is made from heavy gauge anodized aluminum and easily mounts under the generator shelf or other convenient location.

IDEAL FOR:

  • Churches, institutions, and traveling musicians who want to use a Leslie with the organ, but also want to be able to send the organ with rotary effect through a sound reinforcement system
  • Musicians who want a backup plan in case of a Leslie breakdown, lost cable, damaged microphone, etc.

FEATURES:

  • Simple 3 wire organ hook-up
  • Audio level trim adjustment
  • Allows the organ's existing tremolo switch to simultaneously control your existing 122 family Leslie and the Neo ventilator
  • Compatible with standard fast / slow switching as well as fast / slow / stop switching with EIS-122 equipped Leslies

NOTES:  The audio connection between the VIB-3 and the rotary cabinet simulator requires a standard guitar type TS (mono) cable. The speed control connection between the VIB-3 and the rotary cabinet simulator requires a shielded TRS (stereo) cable. These cables are not supplied with the VIB-3.


ETS-2.jpg

TS-2 $109

Mounts in place of  the lower left hand end block on standard Hammond consoles.  Allows convenient rocker switch control of the tremolo function.  Normally provided with a two position switch.  Also available with a three position switch for use with Leslies designed with a stop function. Pre-punched mounting hole provided for addition of a reverb or other control in the same enclosure. 

NOTE: When ordered along with the RV-1D or SSP-3A , the TS-2 can be supplied with the reverb control pre-installed in the end block cover.

SPECIFY LESLIE MODEL(S)


KBF-1.jpg

KBF-1 UPSTOP FELT $9

The KBF-1 is an exact reproduction of the #042-022369 B-3 type upstop felt.  An essential part of any Hammond console restoration or busbar lube job, it helps restore the "new feel" and quiet operation to the keyboard. 

Easily installed on late A-100, B-3, C-3, D-100, and RT-3 organs. (These organs are identified by front strips that are secured with Phillips head screws.) 

Also usable on earlier consoles.  However, front strip removal on these organs requires substantial disassembly of the keyboards.


KBF-2.jpg

KBF-2 $15.50

The KBF-2 is an exact reproduction of the #042-001701 B-3 type downstop felt.  An essential part of any Hammond console restoration or busbar lube job, it helps restore the "new feel" and quiet operation to the keyboard. 

Easily installed on late A-100, B-3, C-3, D-100, and RT-3 organs. (These organs are identified by front strips that are secured with Phillips head screws.) 

Also usable on earlier consoles.  However, front strip removal on these organs requires substantial disassembly of the keyboards. 


FS-100+200.jpg

FS-100 $89 and FS-300 $99 Replacement Front Strips

For later standard Hammond consoles such as the A-100 series, B-3 and C-3. Durable black finish with fine texture. Complete with KBF-1 upstop felt and new black mounting screws.  

NOTE: The FS-300 are screened with the classic gold Hammond logo. Express permission for this use has been granted by Hammond Suzuki.


MRB-MTG.jpg

MRB-MTG Music Rack Base Mounting Screws $6

Exact replacement for the #999-006009 brown oval head mounting screws used to secure the music rack mounting base in standard tonewheel consoles. Replaces missing or damaged originals. Set of 4.


RSP-MTG.jpg

RSP-MTG Mounting Screws $5

Exact replacement for the #841-000001 small black oval head mounting screws used to secure switch plate.  Replaces missing or damaged originals. Set of 4.


TBS-1.jpg

Replacement Thumb Screws
$33.50 per pair

Reproductions of the thumb screws used to secure the back panels of later standard Hammond consoles. 

TBS-1 Solid brass with bright brass finish 
TBS-2 Solid brass with classic brown finish


RSP-0.jpg

RSP-0 BLANK PLATE $23

Identical to the RSP-1, but without the switch holes and lettering.  Useful for covering the reverb control opening in A-100 organs and other custom applications. 


RSP-1.jpg

RSP-1  START / RUN SWITCH PLATE $27.50

Machined from heavy gauge aluminum.  Replaces the #061-023547 thin stamped "instruction plates" used on later A-100, B-3, C-3, D-100 and RT-3 Hammond consoles.  Black anodized finish.  Includes switch mounting hardware. 


OBX-0 / OBX-2 / OBX-3 Series Outlet Boxes

OBX Series Outlet Boxes 

The OBX series of outlet boxes are the same size, shape and color as those originally provided on BV, B-2, and B-3 organs. OBX units may be used to replace damaged or missing outlet boxes as well as to upgrade older consoles not originally equipped with outlet boxes. Designed to be mounted on either side of the console, end to end (multiple units), or in an inverted position (for C style cases). 

OBX-0 $70

Provided with no knockouts or connectors. The blank panel may be punched or drilled by the installer to accept non-standard connectors. May be used in place of, or in addition to a standard outlet box. 

OBX-2 $165

Pre-wired with an original style two conductor AC input connector and 1 tone cabinet connector. (Specify type) Knockouts in unused positions allow future installation of additional tone cabinet connectors. 

OBX-3 $165

Pre-wired with a three conductor (grounded) IEC 320 type AC input connector and 1 tone cabinet connector.  (Specify type)  Knockouts in unused positions allow future installation of additional tone cabinet connectors.

Options: Additional Tone Cabinet Connectors

Each OBX-2 and OBX-3 is built to order and can be supplied with as many as 4 pre-wired tone cabinet connectors in virtually any combination of pre-wired 5, 6, 9 or 11 pin types.
(Do not exceed power switch rating.)


OBX-MTG Mounting Kit  $19

The optional OBX-MTG mounting kit may be used to install the outlet boxes in A-100 organs, cut downs, or other applications where mounting to a flat surface is desired. 

Specify type and quantity of tone cabinet connectors.


GNR-1A  $198.00

GNR-1A $198

GNR-2A $119

GNR-2A   $119

GNR-2A   $119

A cost effective alternative to removing and disassembling Hammond tone wheel generators when defective frequencies are encountered. Simple three wire installation. Generates a sine wave output of any tone wheel frequency. The GNR-1A has a built in power supply and will replace one frequency. Each GNR-2A will replace a single additional frequency, but has no power supply, relying on that of the GNR-1A. As many as three GNR-2A units may be powered by a single GNR-1A.

NOTE: The GNR-1A and GNR-2A are not usable to replace pedal frequencies on spinet organs, since these tone wheel outputs are not sine wave signals. 


EPM-1-2-3.jpg


 

EPM Series Expression Pedal Mats

EPM-1   $14
EPM-2  $9.50
EPM-3  $23

Exact replacements for the adhesive backed expression mats used on many Hammond organ expression pedals. To insure proper adhesion, the old mat as well as its adhesive must be thoroughly removed.  


BE-1A.jpg

BE-1A Blank Left End Block $55
BE-2A Blank Right End Block $43

Replaces the end blocks used on the upper or lower manual of standard Hammond consoles. Allows simple mounting of custom switches or controls in a location easily accessible to the organist. 


CSP-1.jpg

CSP-1 Case Scratch Protectors $44.50

These thin fiberglass sheets are shaped to fit between the keyboards and case of standard Hammond consoles to prevent woodwork damage when raising or removing manuals. Made from durable 1/32" G-10 fiberglass with rounded corners. 


POR-11 Power-On Relay $65

The POR-11 power-on relay is designed to facilitate the installation of 11 pin Leslie speakers on Hammond tonewheel consoles. Unlike the older 6 and 9 pin models, 11 pin Leslies have their own AC mains plug and use a low voltage turn-on circuit. The POR-11 allows these Leslies to be conveniently turned on and off with the existing console power switch, thus alleviating the problems associated with having a separate Leslie power switch.

Exact replacement for the #841-000001 small black oval head mounting screws used to secure switch plate.  Replaces missing or damaged originals. 

Set of 4 


TR-3-transposer.jpg

Trek TR-3 Transposer $299

Works with most Hammond organs utilizing a top octave generator IC. Will allow the organ pitch to be shifted in discrete semitone steps as much as 2 semitones sharp or 4 semitones flat. 

  • Shift your playing into a singer's vocal range
  • Modulate from key to key
  • Accompany other instruments playing in "difficult" keys

NOTE: The TR-3 is not compatible with tone wheel type organs.

SPECIFY ORGAN MODEL AND SERIAL NUMBER