Trek II Leslie Speaker Accessories

Trek II Leslie Speaker Accessories


EIS-122-ELECTRONIC-MOTOR-CONTROL-RELAY.jpg

EIS-122 and EIS-147 Electronic Motor Control Relays $98

The EIS-122 and EIS-147 are solid state devices which provide a silent and extremely reliable alternative to the old style electromechanical relays originally supplied in 122 and 147 type Leslie speakers. Ideal for use in studio, church, and professional applications where quiet switching or ultimate reliability is essential.

These units are fully compatible with existing stock Leslie control circuits and therefore require no changes at the console for standard operation.

For those wishing for more than basic relay replacement, both units also have the capability to add brake-to-off and coast-to-off functions without additional wiring from the console. To utilize these advanced features, a suitable 3 position switch must be supplied by the installer. Three position versions of the TS-2 are available pre-wired specifically for this purpose.


UC-1A.jpg

UC-1A Combo Pre-Amp $619

Allows most single channel Leslie speakers to be driven by your portable organ, guitar, synthesizer or mixer. Two 1/4" phone jack inputs, one for high level signals, one for low level signals. 

FEATURES:

  • Foot switch tremolo control
  • Foot switch power on / off
  • Power and tremolo indicators
  • Input level and tone controls
  • Four different outlets to accommodate each of the Leslie families listed below. May be used singularly or in any combination. (Leslie connector cables not included.)

NOTES: The UC-1A will also function with 700, 705, 710, 720 and 730 type cabinets when the LCO-1 or LCO-1A crossover is installed in tone cabinet.  Model 31H is compatible only if above serial # 5200.  Models 25, 45, 125, and 225 are compatible only if equipped with amplifier.


LBG-10.jpg

LBG-10 Bearing Grommet $11

The LBG-10 is a reproduction of the original #543-051037 grommet used in the lower rotor bearings as well as in the idler spring assembly of many Leslie models. 

Sold in packages of 10 only. 


LCO-1A-new.jpg

LCO-1A Crossover $79

Allows older two channel Leslie speakers like the 710 and 720 to function as single channel cabinets making them much easier to utilize with a wide variety of instruments. As originally manufactured, these older cabinets do not function acceptably with single channel full frequency range signals. 

The LCO-1A provides an active crossover which keeps low bass signals (below 150 HZ) out of the rotary channel where they could cause damage to the small rotosonic speaker. These signals are routed instead through the stationary channel to the 15" speaker where they are properly handled.


LIA1.gif

LIA-1 Idler Assembly – $40

The LIA-1 is an improved version of the original #522-050708 idler spring assembly. A slightly oversized wheel helps provide longer operating life. Used to tension the treble horn drive belt in the following Leslie models: 

21H, 22H, 22R, 45, 47, 51, X77L, X77P, 122, 122R, 122RV, 122V, 142, 145, 147, 147RV, 222, 222RV, 242, 245, 247, 247RV, 251, 257, 351, 357, 600, 710, 760, 770, 900, 910, 925. 

NOTE: The LIA-1 is sold as a complete assembly only.


LP-50.jpg

LPL-60  $22
LPU-60 $22 PULLEYS 

LPL-60  Lower 60 Hz pulley.  Reproduction of the original #522-018309 pulley used to drive the lower rotor in the following Leslie models: 122, 122R, 122RV, 122V, 142, 145, 147, 147RV, 242, 245, 251, 760, 770. 

LPU-60  Upper 60 Hz pulley. Reproduction of the original #522-050500 pulley used to drive the upper horn in the following Leslie models: 21H, 22H, 22R, 45, 45A, 47, 51, X77L, X77P, 122, 122R, 122RV, 122V, 142, 145, 147, 147RV, 222, 222RV, 242, 245, 247, 247RV, 251, 257, 351, 357, 600, 710, 760, 770, 900, 910, 925.